TCK-IP hoist sealing type shaft mining magnetic proximity switch
TCK series magnetic switches have two types: universal type and type (universal type is aluminum shell, type is copper shell, stainless steel shell), and four types of products: TCK-1 type magnetic switch, also known as single point magnetic switch. The TCK series magnetic induction switches are widely used in industries such as metallurgy, machinery, mining, power, railways, and military. Keywords: magnetic switch for hoist cage, wellbore magnetic switch, cage positioning switch, magnetic induction switch, universal magnetic switch, type magnetic switch, permanent magnet sensor, non mechanical contact switch, position sensor, stainless steel switch, mining magnetic switch, hoist electromechanical control magnetic switch, non-contact travel switch, hoist wellbore magnetic switch, limit switch, magnetic sensing magnetic switch, mining sealing magnetic induction switch, magnetic sensor; Working principle TCK-IPTCK-IP diagram of magnetic switch for hoist shaft and mining pouring type magnetic induction switch TCK-IP; TCK-IP hoist sealing type wellbore mining magnetic proximity switch TCK-1T type magnetic switch, used as a magnetic wellbore switch for multi rope and single rope hoists, and also suitable for mechanical equipment as a magnetic proximity switch. The TCK series magnetic switch is a non mechanical contact magnetic proximity switch. It consists of magnetic sensors, electronic circuits, and output switches. When the permanent magnet of the magnetic detection body enters the induction area of the TCK switch magnetic sensor, relying on the magnetic field, the TCK switch operates and outputs a switch signal. The output signal reflects the position and movement direction of the detection body, and serves as a stroke control signal for the control system. It uses weak magnetic sensors and microelectronic devices, with some magnetic sensitivity, high resolution, and wide response frequency. The circuit design adopts technology. There are two types of outputs: AC solid-state switch (SSR) and electromagnetic relay (EMR) contacts. The output switch has a large capacity. The system design adopts reliable technology. Each function is equipped with two sets of circuits, connected in parallel. As long as two circuits with different functions fail simultaneously, the switch can operate normally. There are two types of products, universal and type, suitable for various mines. Due to the comprehensive use of a series of technologies, TCK magnetic switches have achieved good technical indicators and performance, and can work reliably in mine shafts without maintenance. TCK magnetic switch is a new type of wellbore switch that protects the operation of elevators. There are two ways to use it: Shanxi Coal Mine Equipment TCK-1P Mine AC Magnetic Switch Wire Rope Magnetic Source Usage This usage is paired with a wire rope magnetizer and demagnetizer. First, choose a place where the swing of the hoist wire rope is relatively small, such as under the drum, guide wheel, or crown wheel. Install the magnetic switch next to the wire rope, with the switch end face sensor facing the wire rope, and the distance between the switch end face and the rope is less than 50mm. Then use a wire rope magnetizer to magnetize at the corresponding position on the wire rope. During the lifting process, when the magnetization section of the steel wire rope reaches the magnetic switch position, the switch acts and sends out signals such as deceleration. Its application principle is similar to a magnetic tape recorder, which records the position signal on a steel wire rope. During operation, the magnetic switch detects the recording point and sends out a position signal. Usage of permanent magnet magnetic field source; This usage is to fix the permanent magnet on the side wall of the lifting container, install the magnetic switch on the designated position of the wellbore, wellhead, or mast, and make the switch end face sensor run up and down towards the track space of the magnet. During the lifting process, when the magnet on the container reaches the magnetic switch position, the switch acts and sends out signals such as deceleration and parking. Our company's TCK series magnetic switches are mainly used in mine shafts as cage positioning signals and lifting degree indicators. TCK series magnetic switches are widely used and can sense detection objects at 250mm, 360mm, and 500mm, respectively, when used in conjunction with corresponding magnets. There are two types of TCK series magnetic switches: universal type and type (universal type is aluminum shell, type is copper shell, and type is stainless steel shell), and four types of products: TCK-1 type magnetic switch, also known as single point magnetic switch. Shandong Zhuoxin Machinery Co., Ltd. Sales area: Hebei Province, Shanxi Province, Liaoning Province, Jilin Province, Heilongjiang Province, Jiangsu Province, Zhejiang Province, Anhui Province, Fujian Province, Jiangxi Province, Shandong Province, Henan Province, Hubei Province, Hunan Province, Guangdong Province, Hainan Province, Sichuan Province, Guizhou Province, Yunnan Province, Shaanxi Province, Gansu Province, Qinghai Province, autonomous region, Guangxi Province, Xizang, Ningxia, Xinjiang, municipalities directly under the Central Government: Beijing, Tianjin, Shanghai, Chongqing, LJC24A3-T-Z/BIZ capacitive proximity switch, LJC24A3-T-Z/AIZ,LJC24A31-T-Z/CIZ.LJC24A3-T-Z/BZ,LJC2A3-T-Z/AZ,LJC24A3-T-Z/CZ,LJC24A3-T-Z/EZ,LJC24A3-T-Z/ZLJC24A3-T-J/EZ,LJC24A3-T-J/ZLJC30A31-H-Z/BIZ，LJC30A31-H-Z/AIZ,LJC30A31-H-Z/CIZ.LJC30A31-H-Z/BZ,LJC30A31-H-Z/AZ,LJC30A31-H-Z/CZ,LJC30A31-H-Z/EZ,LJC30A31-H-Z/ZLJC30A31-H-J/EM,LJC30A31-H-J/M