Characteristics of magnetic switch CS1-E; Wide voltage range, repeatability, response frequency, strong performance, temperature resistance, good waterproof performance, long service life, convenient installation and debugging. Magnetic Switch CS1-E Image CS1 Series Magnetic Switch Pneumatic System&mash& mash; How to use pneumatic systems correctly? 1. Requirements for designers and users of pneumatic systems. 2. Confirmation of product model and specifications before use& nbsp;     Designers of pneumatic systems and designers of pneumatic components should determine the specifications of pneumatic components based on the performance requirements for the pneumatic system, taking into account performance and potential failures, and based on new product samples and data. If necessary, corresponding analysis and experiments should be conducted. When used in certain emerging industries or industries, it is necessary to collaborate with manufacturers to carry out styling design work in order to *. 2. Special attention should be paid to the following situations: 1) If compressed air is used incorrectly, it can be dangerous. Therefore, the assembly, operation, and maintenance of pneumatic equipment should be trained and experienced; Personnel with certain practical experience will carry out the work; 2) Before confirmation, it is not allowed to use pneumatic equipment or disassemble pneumatic components from the equipment; 3) After confirming that the above treatment has been carried out, cut off the power and air supply, and discharge the remaining compressed air in the pneumatic system before maintenance can be carried out& nbsp; And dismantling; 4) Before starting the pneumatic equipment, it is necessary to confirm that there will be no rapid extension of the plug rod. 2、 The requirements for the use environment of pneumatic systems: 1. When used in environments with corrosive agents, chemicals (such as organic solvents), seawater, water, and non steam, or in places with the above-mentioned substances attached& nbsp; Can be used conditionally, and sealing components, valve bodies, etc. in contact with the medium need to be changed to materials; 2. Avoid using in sexual settings (if necessary, consider taking measures); 3. Do not use in situations with vibration and impact, or the vibration and impact resistance of various pneumatic components should comply with the regulations on the product sample. 4. Do not use in places with heat sources or affected by radiation, or take measures to block radiation heat; 5. In places with strong direct sunlight, add protective covers. Appropriate protective measures should be taken when using in places with high humidity, high dust content, or places with water droplets, oil droplets, cutting oil, or coolant droplets. Magnetic cylinders should not be used in environments with strong magnetic fields. 6. In a temperature environment: 1) In a temperature environment: please use temperature resistant seals; 2) In a warm environment, there may be phenomena such as water freezing and poor operation in the circuit. At this time, attention should be paid to removing water to prevent freezing. 3、 The requirements for compressed air in pneumatic systems: 1. Compressed air discharged by the air compressor cannot be directly used. Compressed air contains a certain amount of water, oil, and dust. After compression, the temperature of the air reaches around 140-170 ℃, and some of the water and oil have become gaseous; 2. Using purified compressed air: 1) Filtering viscosity in general mechanical and pneumatic circuits; 40um； 2) Filtering degree of logic components, jet components, pneumatic motors, etc; 10um； 3) The filtration rate of food, medicine, electronics, tobacco and alcohol, air bearings, etc; 5um； Magnetic switch, CS1-B1, CS1-B1X, CS1-B1N, CS1-B1P, CS1-B2, CS1-B2X, CS1-B2N, CS1-B2P, CS1-B3, CS1-B3X, CS1-B3N, CS1-B3P, CS1-B4, CS1-B4X, CS1-B4N, CS1-B4P, CS1-B5, CS1-B5X, CS1-B5N, CS1-B5P, CS1-B6, CS1-B6X, CS1-B6N, CS1-B6P, CS1-B7, CS1-B7X, CS1-B7X 7N, CS1-B7P, CS1-B8, CS1-B8X, CS1-B8N, CS1-B8P, CS1-A, CS1-AX, CS1-AN, CS1-AP, CS1-E, CS1-EX, CS1-EN, CS1-EP, CS1-M, CS1-MX, CS1-MN, CS1-MP, CS1-G, CS1-GX, CS1-GN, CS1-GP, CS1-T, CS1-TX, CS1-TN, CS1-TP, CS1-J, CS1-JX, CS1-JN, CS1-JP, CS1-U, CS1-UX, CS1-UX 1-UN, CS1-UP, CS1-F, CS1-FX, CS1-FN, CS1-FP model specifications: